Eurotech: Parvus Announces Rugged Tactical Fiber Optic Gigabit Ethernet Switch Subsystem

Parvus DuraNET 1268 Switch Now Available with TFOCA II Fiber Optic Connectors for Military Tactical Deployable Networks

Amaro (Italy) – May 23rd, 2012 – Eurotech subsidiary Parvus announces tactical fiber optic media support for the DuraNET® 1268, a rugged Layer 2 Gigabit Ethernet switch subsystem equipped with ten (10) triple-speed 10/100/1000Mbps ports for connecting IPv4 and IPv6 compatible sensors and computing devices onboard demanding tactical network-centric (un)manned vehicle and aircraft platforms. Designed for rugged extremes, this Size, Weight, and Power (SWaP)-optimized Commercial-Off-the-Shelf (COTS) solution is well suited for C4ISR technology refresh and situational awareness upgrade programs. To enhance reliability, the unit features no moving parts, a near cable-less internal design, all industrial temperature grade components, EMI filtering, and a sealed dust/ waterproof aluminum chassis with isolated MIL-STD-1275/704 power supply that protects against vehicle/aircraft voltage surges, spikes and transients.

Gigabit Ethernet interfaces are brought out over rugged MIL-DTL-38999 connectors on the front panel and now optionally Tactical Fiber Optic Cable Assembly (TFOCA® II) connectors on the rear. These optical interfaces are designed to survive the harshest battlefield conditions and were selected by the U.S. ARMY WIN-T program as the standard next generation fiber optic connector for military tactical deployable networks.

Managed and unmanaged switch configurations are available for configurable or “plug and play” Gigabit Ethernet LAN applications. The base DuraNET® 1268 was previously qualification tested for extreme MIL-STD-461F EMI/EMC and MIL-STD-810G thermal, shock, vibe, humidity, altitude, and ingress conditions, as well as RTCA/DO-160G airworthiness tests for low temperature and high altitude operation.

The DuraNET® 1268 features an onboard microprocessor for local/remote control and port monitoring, as well as support for Quality of Service (QoS) traffic prioritization, Virtual Local-Area Network (VLAN) trunking, Telnet remote CLI management, and Rapid Spanning Tree (RSP) redundancy. To enhance security and system management, the unit integrates recoverable data zeroization capabilities for declassifying switch data, along with RS-232 Command Line Interface (CLI) and Ethernet management ports. Status LEDs indicate zeroization signal, power, and port link/speed/activity.

AVAILABILITY
DuraNET 1268 subsystems with fiber optic support will begin in Q3 2012. Contact sales@eurotech.com for pricing and updated production availability information. For additional specifications or to download a product datasheet, visit http://www.eurotech.com/en/products/DuraNET 1268.

Advertisements

Eurotech Receives 2M USD Follow-On Order for Catalyst TC Embedded Module for Homeland Security and Defense Application

Cross Match orders more embedded modules to support production of its handheld biometric identity device

Amaro (Italy) – April 16th, 2012 – Eurotech, a leading supplier of embedded technologies, products and systems, today announces Cross Match has issued a $2 million purchase order for the Catalyst TC module, which is used in its handheld device for homeland security and defense applications. The modules will be delivered over the next 12 months.
The Catalyst TC, based on the Intel Atom processor E6xx series, is a highly integrated and flexible embedded module that offers multiple communications, I/O, and multimedia capabilities with low power consumption in a small footprint.
“We have a need for more Catalyst TC units because we have seen an increased demand for our products,” said Shawn Mokhtari, Cross Match Technologies Senior VP of Technology. “Eurotech has been reliable and on time for the duration of our relationship, and we look forward to working with them as we continue to deliver our biometric identity solutions to the marketplace.”
The Cross Match product is a homeland security and defense solution that also offers optional 3G communications support and built-in wireless networking capability that allows field personnel to access remote databases as part of a biometric identity solution.
“Cross Match biometric products are extremely important to many people, and it’s gratifying to be part of their solutions” said Greg Nicoloso, CEO of Eurotech in North America. “Our Catalyst line of computer on module boards helps customers with demanding requirements and we look forward to addressing the next challenging project.”

Eurotech Receives 2M USD Follow-On Order for Catalyst TC Emb …

Eurotech riceve ulteriore ordine di 2M USD per il modulo Catalyst TC, per applicazioni nella difesa e nella sicurezza nazionale

Cross Match ordina ulteriori moduli per sostenere la produzione del suo dispositivo portatile di identificazione biometrica ….

Eurotech riceve ulteriore ordine di 2M USD per il modulo Cat …

 

Catalyst TC
Catalyst TC

Una nuvola di dati

Roberto Siagri di Eurotech ci racconta le potenzialità del cloud computing per aziende ed enti pubblici

Cloud, ovvero nuvola.   ….   Con Roberto Siagri, amministratore delegato di Eurotech, abbiamo tracciato un quadro di come funziona questo nuovo potente strumento, anche giocando con automobiline elettriche e macchine per le bibite…  ”

link al video su Triwu.it  Una nuvola di dati – sommario smart city – TRIWU’ – il sito

Eurotech: €1.2M order for Aurora HPC from German Research Centre Jülich

 

Amaro (Italy) – April 5th, 2012 – Eurotech, a leading company in embedded and supercomputing technologies, announces that it has received a 1.2 million euro order from Forschungszentrum Jülich, one of the largest research centres in Europe, for supply of a HPC (High Performance Computing) system of the Aurora family. Delivery is scheduled to take place within this year.
The Aurora HPC will be used within the scope of the EU-funded project DEEP (Dynamical Exascale Entry Platform), an innovative European response to the challenge of creating supercomputers capable of performing ExaFlops, i.e. a billion billion calculations per second, that is a thousand times faster than today’s fastest supercomputers.
The DEEP consortium, led by Forschungszentrum Jülich, proposes to develop a novel, Exascale-enabling supercomputing architecture that takes the concept of compute acceleration to a new level: instead of adding accelerator cards to Cluster nodes, an accelerator Cluster, called Booster, will complement a conventional HPC system and increase its compute performance. While the Cluster is an off-the-shelf component, the Booster will be designed and built by the DEEP project partners using cutting edge technology. Together with a software stack focused on meeting Exascale requirements, comprising adapted programming models, libraries and performance tools, the DEEP architecture will enable unprecedented scalability. In the DEEP consortium Eurotech will be the responsible to assemble and design the cabinets, racks and blades of the system.

Note: the DEEP project will be funded by the European Commission, under the Seventh Framework Programme (FP7-ICT-2011-7, Integrated Project No. 287530).

Eurotech: ordine di €1,2M per HPC Aurora dal Centro di Ricerca tedesco Jülich

 

Amaro (UD) – 5 aprile 2012 – Eurotech, azienda leader nelle tecnologie embedded e di supercalcolo, annuncia di aver ricevuto un ordine di 1,2 milioni di Euro da Forschungszentrum Jülich, uno dei più grandi centri di ricerca in Europa, per la fornitura di un sistema HPC (High Performance Computing) della famiglia Aurora. La consegna è prevista quest’anno. 
L’HPC Aurora sarà utilizzato nell’ambito del progetto finanziato dall’UE denominato DEEP (Dinamico Entry Exascale Platform), una innovativa risposta europea alla sfida di creare supercomputer in grado di raggiungere gli ExaFlops, vale a dire un miliardo di miliardi di calcoli al secondo, ovvero un migliaio di volte più veloci rispetto ai più veloci supercomputer di oggi. 
Il consorzio DEEP, guidato da Forschungszentrum Jülich, si propone di sviluppare un’innovativa architettura di supercalcolo di classe Exascale, che porti il concetto di accelerazione dell’elaborazione ad un nuovo livello: invece di aggiungere schede di accelerazione ai nodi di un Cluster, un Cluster acceleratore, chiamato Booster, integrerà un sistema HPC convenzionale e ne aumenterà la potenza di calcolo. Mentre il Cluster sarà un componente off-the-shelf, cioè disponibile sul mercato, il Booster sarà progettato e costruito dai partner del progetto DEEP con tecnologia all’avanguardia. Grazie anche ad un pacchetto software focalizzato sulla soddisfazione delle esigenze specifiche di una piattaforma Exascale, che comprende modelli di programmazione adeguati, librerie e strumenti di ottimizzazione delle performance, l’architettura DEEP consentirà una scalabilità senza precedenti. All’interno del consorzio DEEP, Eurotech sarà responsabile della progettazione e assemblaggio degli armadi, dei cestelli e delle schede del sistema. 

Eurotech Announces SekuPLATE, License Plate Recognition Systems for Security and Surveillance Applications

SekuPLATE license plate recognition systems achieve high detection rate in all light and weather conditions

Amaro, Italy – March 21, 2012 – Eurotech, a leading supplier of embedded technologies, products and systems, today announces the launch of SekuPLATE, a new family of IP-based SekuPLATELicense Plate Recognition Systems that target demanding security and surveillance applications where intelligent association of vehicles and permission rights is needed. Based on cutting-edge recognition algorithms, SekuPLATE delivers top-notch reliability plate recognition systems, that dramatically minimize detection failures.

Compact, versatile, and easily configurable, SekuPLATE systems read license plates and process them automatically, to monitor the passage of vehicles through toll gates, checkpoints, access areas, parking lots and other similar applications. SekuPLATE delivers extreme reliability, with an accuracy rate on detections of 95% for front plates and 98% for rear plates, in all light and weather conditions. The design is compatible with traditional IT architectures and also benefits from connectivity to Eurotech’s cloud platform, dramatically cutting time-to-market when building scalable, robust applications that integrate devices with business applications.

SekuPLATE products are now available to process license plates of European countries, Turkey, Morocco, South Africa, Brazil, Argentina, and also for plates featuring Arabic characters.

Eurotech annuncia SekuPLATE, la sua nuova famiglia di sistemi di lettura targhe per applicazioni di sicurezza e sorveglianza

I sistemi di lettura targhe SekuPLATE garantiscono elevata affidabilità in tutte le condizioni climatiche e di luminosità

maro, Udine – 21 Marzo 2012 – Eurotech, fornitore leader di tecnologie, prodotti e sistemi embedded, annuncia il lancio di SekuPLATE, una nuova famiglia di Sistemi di Lettura Targhe basati su IP e destinati ad applicazioni di sicurezza che richiedono l’associazione intelligente di veicoli e permessi di accesso. Grazie ad avanzati algoritmi di riconoscimento, i sistemi di lettura targhe SekuPLATE assicurano un’elevata affidabilità che riduce notevolmente gli errori di identificazione. 

Eurotech Announces SekuFACE, Biometric Face Recognition Systems for Security Applications

SekuFACE biometric face recognition systems are compliant with ICAO standard (ISO/IEC 19794-5) and achieve high accuracy rate in all light condition

Amaro, Italy – March 26, 2012 – Eurotech, a leading supplier of embedded technologies, SekuFACEproducts and systems, today announces the launch of SekuFACE, a new family of IP-based Biometric Face Recognition Systems that target demanding security applications where intelligent association of personal identity and permission rights is needed. Based on biometric mapping of face images and their automatic validation against the ICAO standard (ISO/IEC 19794-5), SekuFACE systems dramatically simplify compliancy and privacy issues, while providing at the same time fast and reliable facial recognition.

SekuFACE systems detect human faces and match them with reference biometric tracks allowing to identify the subjects and monitor their transit through checkpoints and access passages in restricted areas. SekuFACE delivers extreme reliability, with an accuracy rate of 95% in any light condition. Accordance with ICAO standard ensures consistent quality of all samples while biometric mapping and user-configurable automatic deletion policies streamline the compliance of installed systems with privacy regulations.

SekuFACE enables effective monitoring of large structures by activating multiple access security levels, tracking simultaneous targets and managing hierarchical access gates. Easy to be interfaced with other data sources, such as personal ID lists and badge readers, SekuFACE is also naturally suited to implement cross-checking of credentials for an higher level of security.

For more info, please visit http://www.eurotech.com/en/products/SekuFACE

DynaCOR 10-00: Eurotech Announces Rugged Industrial Computer for Demanding Machine-to-Machine Applications Eurotech Announces Rugged Industrial Computer for Demanding Machine-to-Machine Applications

DynaCOR 10-00 Leads a new Family of Gateways for rugged M2M Applications featuring a modular fanless design offering IP65 certification

DynaCOR 10-00Amaro, Italy – February 28, 2012 – Eurotech, a leading supplier of embedded technologies, products and systems, today announces the launch of the EN50155 rated DynaCOR 10-00, a new family of rugged mobile computer that targets demanding machine-to-machine (M2M) applications. Based on the Intel® Atom™ processor, the DynaCOR 10-00 is a purpose-built, low power, mobile computer platform with wide range power supply and IP65 protection.

The DynaCOR 10-00 system is modular and versatile with a fanless design and rugged connectors for long-term reliability in harsh environments. Application specific configurations are easy to implement in several vertical industries enabling reliable M2M solutions even under the most demanding conditions: with a low power, highly efficient design, the DynaCOR 10-00 is a dependable platform featuring CPU speeds of 1.1GHz, 512MB RAM and a 2 GB flash disk.

“Eurotech’s powerful and rugged platforms are the ideal building blocks for smart M2M architectures,” said Robert Andres, Eurotech Group Marketing Director. “The DynaCOR 10-00 is designed to speed-up and simplify the design and deployment of M2M applications in harsh environmental conditions. The DynaCOR 10-00 combines hardware features and certifications with Eurotech’s End-to-End Cloud solution; for OEMs, integrators and even individual developers this is a quantum leap in terms of savings and improved time-to-market.”

The DynaCOR 10-00 rail rated platform is purpose built for the transportation and heavy industrial markets leveraging Eurotech’s Everyware Software Framework (ESF) to speed up M2M application software development. The design also the benefits from connectivity to the Everyware Cloud, Eurotech’s M2M cloud platform, dramatically cutting time-to-market when building scalable, robust applications that integrate devices with business applications.

Eurotech: Japanese Subsidiary Advanet Obtains €4M Design Win For Intelligent Transportation Systems

Amaro (Italy) – February 2nd, 2012 – Advanet Inc, fully own subsidiary of Eurotech Spa, today announces a design win for embedded computers to be used within Highway Intelligent Transportation Systems to de deployed in Japan.

The total sales volume is expected to be of 4 million Euro. Deliveries will begin in second half of 2012 and will be completed in about 3 years. Due to agreements with the Customer, no further details can be disclosed.

“Intelligent Transportation Systems are at the state-of-the-art in Japan and we are pleased to have been chosen by a major player in this field for such an interesting project” said Shoji Fuchigami, CEO of Advanet Inc.

Eurotech: Japanese Subsidiary Advanet Obtains €4M Design Win …

Eurotech: la società giapponese Advanet ottiene design win da €4M per sistemi di trasposto intelligente

Amaro (UD) – 2 Febbraio 2012 – Advanet Inc, società controllata integralmente da Eurotech Spa, ha annunciato oggi di aver ottenuto un design win per computer embedded che verranno utilizzati in sistemi di trasporto intelligente da installare in alcuni tratti autostradali in Giappone.

Il volume totale atteso delle vendite ammonta a 4 milioni di Euro. Le consegne inizieranno nella seconda metà del 2012 e saranno completate nell’arco di 3 anni. In virtù di accordi con il Cliente, nessun ulteriore dettaglio può essere rivelato.

“I sistemi di trasporto intelligente sono allo stato dell’arte in Giappone e siamo lieti di essere stati scelti da un’azienda primaria in questo campo per un progetto così interessante” ha detto Shoji Fuchigami, CEO di Advanet Inc.

 

Podcast: Eurotech Leverages Mfg Excellence for HPC Market

Podcast: Eurotech Leverages Mfg Excellence for HPC Market | insideHPC.com

” In this this podcast Giovanbattista (Giovanni) Mattiussi from Eurotechdiscusses the company’s push into the HPC market and their growing presence at the annual SC and ISC conferences. Widely known for their embedded manufacturing capabilities, Eurotech is receiving accolades for their high-density Aurora Intel-based clusters.
Download the MP3 * Subscribe on iTunes * Subscribe on other podcast players. If your IT Crowd blocks Dropbox, you can download the audio from this Google page. …. “

… read more  at InsideHPC…

HPC, High Performance Computing provided by Eurotech